Do your dog usually escape from your sight? Are you looking for a guide to install an underground dog wire fence? If yes then you are absolutely on the right spot because here I am going to discuss the requirement of a dog wire fence and the proper step by step method to easily and securely bury it.
There are several methods to control and supervise your pet. This includes the old traditional methods or wooden or net fencing as well as the ones in which you put a collar or chain in your dog’s neck. However, through these techniques, there are numerous chances that your dog might get away or escape. In this regard, dog wire fences play a vital role in monitoring your dog.
How to Easily and Safely Bury a Dog Wire Fence?
Some people purchase the dog wire fence but they are not aware of the method to install it. So, they simply staple the wire fence above the ground or attach it with the traditional wooden fencing system. There is no doubt that this process seems so rapid and fast but in reality, it is the least productive method of installing this wire fence.
Items You Need
For the sake of installing a worthy dog wire fence, you will be needing several tools which include an electric wire or fence, a fence and corner insulators, transmitter box, electric fence charger, hammer, wire cutters, and some nails or clamps to bury the fence underground ranges from 2 to 6cm below, because the deeper you install it, the lesser signals will transmit.
For the first step, you need to plan the territory in which your dog can roam around freely and safely. If you have a huge garden or lawn in which you want to develop this dog wire fence then there must be some area of the space from where you want your dog to stay away. So, you need to plan that area from where your dog is prohibited, to provide an accessed area to your dog.
Then you need to mark various spots where you will bury the corner and fence insulators that are intended to withstand the extra strain created by the fence line pulling from the anchor point. As well as the transmitter box. It releases a sign that is transferred through your fence wire, making the line that your dog can’t cross. From the transmitter, you can set the width of the fence, or how close your dog gets to the wire before you notice and caution start.
Before you even start to design the format of your fence establishment, you should set aside the effort to attentively and completely distinguish the entire locations of obstacles present underground because in most cases there are utility lines present, much deeper than you dig, but still, it is important to identify and avoid them rather than regretting later.
For the next step, use a trencher or any tool that assists you in digging the ground for about 2 to 6cm down with a proper structure in your mind. Whenever you have the border marked and dug you can bury the wire in and pack up the dirt to seal the wire setup. The deeper you put the wire the more perfect it will fit in without being displaced or damaged.
Locating Transmitter Box
After burying the underground fence, it’s essential to factor the area of the transmitter confined to the last plan of your fencing design. Numerous individuals decide to locate their transmitter box near an outside mass of their home, because of the requirement for an outer electrical plug. If so, you may have to utilize wound wire procedures to make a fencing territory around the whole border of your property.
For this procedure, you need to initially begin by running the wire from the transmitter box to the end of the ideal fence area. At that point, run the wire around the whole limit of your property, until you arrive at where you began. You would then be able to wind the wire back that was utilized to reach from the transmitter box to the external border. This method will cancel the radio signals, thus allowing your dog to pass safely.
Settling the Transmitter Box
The last step for the successful burial of the dog fence wire is the mounting of the transmitter box. The transmitter box is also known as the control box because, through this, signals are produced which are later on transmitted through the fence territory wire. The control box will permit you to change the limit width of your fence, which will figure out where the caution zone and the warning zone will begin. Sometimes, you can likewise utilize the transmitter box to set the strength of the correction sensation.
Checking the Fence
When you have properly done every step, you need to find out and make sure that everything is working properly or not. For this purpose, you need to test the process with your dog. When your dog wire fence is utilized, it will provide a warning signal when your dog is about to cross the territory, and if your dog doesn’t stop to the caution signal, then it will receive a correction sensation. You can also go for a GPS dog fence if you don’t want to take this whole process. Simply, click here to know more about it.
If things are working accordingly this way, then you can ensure that you have successfully buried a dog wire fence. If something goes wrong, recheck all the procedures and correct the issue.
Guides That Help You: